Telular SX7M Manual de usuario

07/13/07 Part Number 56038501Wi PATHTMSX7T Terminal and SX7M ModemUser GuideGSM/HSDPA

Setting Up Your Wireless WAN Data ConnectionOnce the computer and the SX7 are connected and powered up, you will need to set up yourWireless WAN data

3. From the Home screen, click Setup (1) > Wireless WAN (2).4. For PSD Auto Connect, click Always On (3).5. For Context APN (4), make sure the ISP

9. To confirm your data connection, click Status (1). The Status > Router page willauto-refresh every few seconds. Your WAN address from your wirel

Status LEDsIn addition to checking your status through the Telular Device Manager on your computer, youcan also use the LED indicators on the unit for

Using the USB Connection OptionThe preferred method for establishing a data connection with the SX7 is through the EthernetPort (see “Connect the SX7

Connect the SX7 to Your Computer With a USB Cable1. With your computer and the SX7 powered on, connect the terminal end of the USB cableto the USB Typ

USB Connection OptionWi PATHTMSX7 14 User Guide On the Select a Device screen, select Modem - SX7 USB Modem and deselect anyother hardware listed. O

4. The Connect dialog will open. Click Properties > Options. Uncheck Prompt for phonenumber and Prompt for name and password, certificate, etc.. Se

Using the Voice and Fax Options (SX7T Only)The Wi PATH SX7T Voice/Fax/Data terminal lets you use your wireless service provider forvoice calling and f

Using the Fax Function on Your SX7T1. To use your SX7T’s fax feature, you will first need to set up your device to support faxdata. The Telular Device

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Getting

 For RJ-11 Jack Mode (4) select J1 Voice, J2 FAX or J1 Voice, J2 Auto. Click Save (5), and then click Restart (6) to save your settings and restart

Voice/Fax ProgrammingThe Telular Device Manager allows you to program all the voice and fax options for service onyour SX7T.1. From your Web browser,

Basic (cont.)RJ-11 Jack ModeSelect a configuration for the Phone jack (J1) and theFax jack (J2):J1 Voice, J2 Voice to set both jacks for voice calls o

TipYou can also program certain voice and fax options for your device using POTS (Plain OldTelephone Set) commands on your phone.Please see the refere

Advanced Data Connection OptionsThe following pages outline all the advanced programming options and settings availablethrough the Telular Device Mana

DHCP Settings DHCP Server (Ethernet only): Dynamic Host Configuration Protocol. Select Enable toallow the unit to receive IP address, subnet mask, de

Setup > Keep AliveKeep Alive lets you prevent the wireless network from closing your data connection duringextended periods of inactivity by having

Setup > DDNSDDNS (Dynamic Domain Name Server) settings allow the SX7 to be accessed via the Interneteven when dynamic IP addresses are being assign

Setup > SIMThese options allow you to enter a PIN number for SIM card access (if necessary). Your SIMcard may be set to operate without a PIN being

Network OptionsNetwork > RoutingRouting settings allow you to control the unit’s network routing configuration. There aretwo primary options availa

IntroductionThank you for choosing the Wi PATHTMSX7 as your wireless data connection solution.The SX7T Voice/Fax/Data Terminal and the SX7M Modem each

 Router (NAT off): (Default setting) In addition to the options available under Gatewaymode, Router mode offers the following options:● Dynamic Routi

Network > Firewall/FiltersThe Firewall/Filters settings allow you to customize the following access settings for the SX7on your network. Firewall

Network > Port ForwardingThis screen allows you to enter an Application Name, Port Extension range, select TCP orUDP protocols (or both), and compl

Administration OptionsAdmin > ManagementThe Administration > Management screen allows you to change the following settings. Device Manager User

Admin > Factory DefaultsClick Restore Defaults to reset all the device settings to the factory default settings. Anysettings you have customized th

Status OptionsThe screens available under the Status menu provide information about your unit. The fields inthe Status screens cannot be edited direct

 Service Provider Name: The name of the wireless service provider for your unit (forexample, ABC Wireless). Radio Service Type: This displays your c

Status > LAN USBStatus > Wireless WAN StatusAdvanced Data Connection OptionsWi PATHTMSX7 35 User Guide

PSTN OptionsSee “Voice/Fax Programming” on page 19 for available PSTN (Public Switched TelephoneNetwork) options. Below are examples of each of the PS

PSTN > POTS SetupAdvanced Data Connection OptionsWi PATHTMSX7 37 User Guide

Set Up Your SX71. Install the SIM Card into the SIM card holder in the battery compartment. If applicable, remove the SIM Card from the larger plasti

Advanced SettingsThis section explains some of the advanced configuration settings that may be required insome instances to make the SX7 operational o

GlossaryAPN - Access Point NameDDNS - Dynamic Domain Naming SystemDHCP - Dynamic Host Configuration ProtocolDial Tone - The tone heard when a phone re

SIM Card - Subscriber Identity ModuleStatic DNS - Static Domain Naming SystemTCP - Transmission Control ProtocolUDP - User Datagram ProtocolUMTS - Uni

3. Connect and hand-tighten the TNC Antennas. Once they are installed, orient the antennasso they point upward (vertical orientation). This is the typ

5. (Optional) For optimal performance and protection, you may elect to connect a copper wire(not included) to the protective earth Ground Connector Sc

Connect the SX7 to Your ComputerBefore you connect your computer, ensure you do not have an existing landline dataconnection and that you have either

Using the Telular Device ManagerThe Telular Device Manager will allow you to configure all your connections, view your status,and manage all your conn

2. On the Home screen (see below), you will see the unit’s Model number, the Time, andyour Wireless WAN connection status.3. Click an item in the colu